To remove the oil sump temperature/oil level sensor, first remove the oil pan.
Replace the oil sump temperature/oil level sensor
Unplug the temperature/oil level sensor from the cable (1).
Loosen screw (2).
Dismount temperature sensor / oil level sensor.
Replace the oil sump temperature/oil level sensor
Screw the holder (2) with pipe (1) and tube with cable (3) tight to the housing with a hexagon bolt M10 x 20 - 8.8 (4).
Tightening torque 46 Nm.
Screw the temperature/oil level sensor M6 x 30 - 10.9 (7) tight with screw (6).
Tightening torque 14 Nm.
Insert the two plugs (5) into the temperature/oil level sensor (7).
Install the directly wired temperature/oil level sensor
Mount the oil level sensor (1).
Insert the plug (2) on the oil level sensor (1).
Make sure that the guide tube of the oil dipstick (3) is guided through the bore in the butt strap (4).
Screw the pipeline with holder (5) with a hexagon bolt (6) to the transmission housing.
To remove the converter temperature sensor, the control block cover must first be removed.
Removing the oil temperature sensor
Unplug the plug connection between the cable harness and connection to the oil sump temperature sensor/oil level sensor (2) with special tool (1).
Unplug the plug between the cable harness and converter oil temperature sensor (3).
Unscrew the converter oil temperature sensor.
Unscrew the permanently wired converter temperature sensor from the adapter screw.
The converter temperature sensor is permanently connected with the cable harness.
Mounting the converter temperature sensor
1. Adapter screw for converter temperature sensor
2. Connection to the temperature/oil level sensor in the oil sump
Screw in the adapter screw for converter temperature sensor M14x1.5 (1).
Tightening torque 15 Nm.
Use special tools
Installing the directly wired temperature sensor
Screw the directly wired converter temperature sensor into the adapter screw.
Insert the plug to the oil sump temperature/oil level sensor (2) with the special tool.
Tighten union nut (1).
Tightening torque 15 Nm.
NOTICE
Never use an impact screwdriver to dismount the speed sensors!
Speed sensors can be damaged.
Dismount the speed sensors carefully manually with suitable tools.
Disconnect the plug connectors of the speed sensors from the cable harness.
Unscrew screws from the speed sensors.
NOTICE
Incorrect distance between speed sensors and pulse-generator wheel!
Risk of destruction of speed sensors.
Adjust distance with spacers.
NOTICE
Mount the speed sensors only with suitable tools!
Speed sensors can be damaged.
Never use an impact screwdriver to mount the speed sensors.
Insert new speed sensors.
Set the distance between the speed sensors and the pulse-generator wheel using spacers.
The distance must be between 0.8 and 2.5 mm.
For N1 and N2, spacing washers are available for setting the distance between the speed sensor and the rotary sensor.
Reuse installed spacers.
Tighten the screws on the speed sensors.
Tightening torque 9 Nm.
Replace the oil sump temperature/oil level sensor
To remove the oil sump temperature/oil level sensor, first remove the oil pan.
Unplug the temperature/oil level sensor from the cable (1).
Loosen screw (2).
Dismount temperature sensor / oil level sensor (3).
Mount the sensor (3).
Tighten the screw (2).
Tightening torque 9 Nm.
Plug in the connector (1).
Replacing the converter temperature sensor
To remove the converter temperature sensor, the control block cover must first be removed.
Unscrew the converter temperature sensor (1).
Screw in the converter temperature sensor (1).
Tightening torque 20 Nm.
NOTICE
Never use an impact screwdriver to dismount the speed sensors!
Speed sensors can be damaged.
Dismount the speed sensors carefully manually with suitable tools.
Unscrew screws from the speed sensors.
Remove the speed sensors.
NOTICE
Incorrect distance between speed sensors and pulse-generator wheel!
Risk of destruction of speed sensors.
Adjust distance with spacers.
The distance must be between 0.8 and 2.5 mm
or
Reuse installed spacers.
NOTICE
Mount the speed sensors only with suitable tools!
Speed sensors can be damaged.
Never use an impact screwdriver to mount the speed sensors.
Insert new speed sensors.
Set the distance between the speed sensors and the pulse-generator wheel.
For N1 and N2, spacing washers are available for setting the distance between the speed sensor and the rotary sensor. The distance must be between 0.8 and 2.5 mm.
Tighten the screws on the speed sensors.
Tightening torque 9 Nm.
The converter temperature sensor and the temperature/oil level sensor in the oil pan are now permanently wired due to the risk of sudden temperature fluctuations.
Replace the converter temperature sensor completely, together with cable and sensor
For this, remove the control block cover and control blocks.
Replace the oil sump temperature sensor / oil level sensor completely, together with cable and sensor.
For this, remove the oil pan.